2D and 3D silicone printing and heat transfer labels for garments and sportswear. Wash-resistant, soft-touch, embossed logos. Custom branding for apparel producers.
Silicone printing gives apparel a raised, soft-touch logo that survives repeated washing. We produce heat transfer labels for sportswear, caps, bags and promotional garments.
| Process | 2D flat silicone printing, 3D raised / embossed silicone printing |
|---|---|
| Material | Liquid silicone rubber (LSR), platinum-cured, phthalate free |
| Thickness | 0.3 mm to 3 mm depending on the emboss height required |
| Substrates | Cotton, polyester, blends, nylon, caps, bags, webbing, elastic |
| Transfers | Heat transfer labels, screen printed transfers, silicone badge patches |
| Application | Heat press, typically 150-170 C for 10-20 seconds at medium pressure |
| Wash resistance | 40+ domestic wash cycles with correct application (indicative) |
| Finish | Matte, gloss, soft-touch, metallic, glow-in-the-dark, fluorescent |
| Compliance | OEKO-TEX and REACH conforming silicone available on request |
| MOQ | From 500 pieces per design |
Silicone printing deposits liquid silicone rubber through a screen onto a garment or onto a transfer film, then cures it with heat into an elastic, rubber-like layer. Because the layer is silicone rather than plastisol, it stays flexible, does not crack when the fabric stretches, and has a distinctly soft, slightly rubbery hand feel that brands use as a quality signal on sportswear and streetwear.
It is the only common decoration method that keeps a sharp raised edge on stretch fabric. A plastisol puff print looks raised on the shelf but flattens and cracks once the garment is worn and washed; a silicone print keeps its profile.
In 2D printing the silicone is laid down in a flat layer, usually two to four passes, giving a smooth raised surface a fraction of a millimetre high. It is used for logos, small text and full-width prints where the garment still needs to drape.
In 3D printing the silicone is built up through repeated passes with a domed screen profile, producing a clearly embossed badge with crisp edges — the logo you see on performance sportswear and technical outerwear. Heights of one to three millimetres are typical. 3D costs more because of the extra passes and curing time, and it needs a firmer substrate behind it, so it is normally applied as a badge or patch rather than directly onto thin fabric.
Silicone can be printed onto a release film to make a heat transfer label or a badge. That decouples production from garment production: we print and cure the badges, ship them flat, and your factory applies them with a heat press at the end of the line. This is the usual route for brands whose cut-and-sew is done in a different country from the branding.
We supply the application parameters — temperature, dwell time, pressure and peel method — with every shipment, because almost every adhesion failure we are asked about traces back to a press that was too cool or a dwell that was too short.
Correctly applied silicone prints survive more than forty domestic wash cycles without cracking, peeling or losing definition, and they resist dry cleaning and industrial laundering better than most alternatives. They are also stable at high temperature, which matters for workwear that is tumble dried hot.
We use platinum-cured, phthalate-free silicone and can supply OEKO-TEX and REACH conforming material where your market or your brand compliance requires it. Tell us the standard when you enquire so it is built into the quotation.
Sportswear and team kit logos, performance and outdoor apparel branding, caps and headwear, bags and backpacks, webbing and elastic straps, socks and grip patterns, workwear and uniform badges, promotional garments, and medical or grip textiles where the silicone is functional rather than decorative.
Silicone printing reproduces bold shapes best. Keep strokes above roughly 1 mm, avoid fine serif text below about 8 pt, and supply vector artwork. Very fine detail is lost when the silicone flows and levels during curing. For 3D badges, send the outline as a separate vector layer so the screen can be built to the right profile.
Send your artwork, size, material preference, quantity and destination. We quote within one working day with a material recommendation and a lead time. If you are not certain which material suits the application, describe where the product will be used and we will specify it for you.
We then produce a sample on the same production equipment as the bulk order, so what you approve is what you receive. After sample approval we run production, inspect, and pack for export — flat packed, rolled or boxed depending on the product — with documentation prepared for your destination. Shipment is by sea, air or courier.